HP LaserJet 600 M602N Laser Printer - Monochrome - 1200 x 1200 dpi Print - Plain Paper Print - Desktop - 52 ppm Mono Print - 600 sheets Input - Manual Duplex Print - LCD - Gigabit Ethernet - USB

Error Codes and Support

Error:

[File System] device failure To clear press “OK” Cartridge Memory Abnormal
[File System] file operation failure To clear press “OK” Cartridge Out
[File System] file system is full Checking engine
[File System] is not initialized Checking paper path
[File System] is write protected Chosen personality not available To continue touch “OK”
{binname} full Remove all paper from bin Cleaning do not grab paper
{Supply} low OR Supplies low Cleaning…
{Supply} very low OR Supplies very low Clearing event log
10.00.33 Clearing paper path
10.00.35 Close stapler/stacker multi bin mailbox door
10.00.60 Close top cover
10.00.69 Cooling device
10.00.91 Creating cleaning page…
10.23.35 Data received To print last page press “OK”
10.23.50 Event log is empty
10.23.51 Expected drive missing
10.23.52 External device initializing
10.23.60 Face Down Tray Full
10.23.70 Printing Past Very Low FIM Load Error Send full FIM on {X} port
10.26.15 Fuser Kit low
10.26.50 Fuser Kit very low
10.26.60 Genuine HP cartridge installed
10.XX.34 Used Supply In Use Genuine HP supply installed
10.XX.40 Genuine HP Supplies Installed HP Secure hard drive disabled
10.XX.41 Unsupported Supply In Use Incompatible {supply}
10.XX.70 Printing past very low Incompatible supplies
10.YY.15 Install {supply} Initializing…
10.YY.35 Incompatible {supply} Install fuser unit
11.00.YY Internal clock error Install supplies
13.00.00 Install supply
13.00.EE Internal disk device failure
13.A3.FF Internal disk file operation failed
13.D3.DZ Internal disk file system is full
13.E5.FF Internal disk is write protected
13.EA.EE Internal disk not found
13.EE.FF Internal disk not functional
13.FF.EE Internal disk not initialized
13.FF.FF Internal disk spinning up
13.WX.EE Job not stapled due to mixed sizes
13.WX.FF Load Tray {X}: [Type] [Size]
13.WX.YZ Fuser Area Jam Load Tray {X}: [Type] [Size] To use another tray press “OK”
13.WX.YZ Jam below control panel Loading program {XX}
13.WX.YZ Jam in Tray {X} Manually feed output stack
13.WX.YZ Jam in Tray 1 Manually feed: {Type}{Size}
13.WX.YZ Jam inside envelope feeder Manually feed: {Type}{Size} To use another tray press “OK"
13.WX.YZ Jam inside top cover Memory tag missing (Y = 1)
14.00.XX Moving solenoid
20.00.00 Insufficient memory: {Device} To continue touch “OK” Moving solenoid and motor
21.00.00 Page Too Complex No job to cancel
32.08.AX NON HP SUPPLY INSTALLED
32.21.00 Output Bin Full
33.01.XX Paused…
33.XX.YY Used board/disk Performing Paper Path Test…
40.00.01 USB I/O buffer overflow To continue touch “OK” Please Wait…
40.00.02 Embedded I/O buffer overflow To continue touch “OK” Printing Configuration…
40.00.05 Embedded I/O bad transmission To continue touch “OK” Printing Event Log…
41.02.00 Error Printing File Directory…
41.03.YZ Unexpected size in envelope feeder To use another tray touch"Options" Printing Font List…
41.03.YZ Unexpected size in tray {X} Printing Fuser Test Page…
41.05.YZ Unexpected type in tray {X} Printing Help Page…
41.XX.YZ Error To continue touch “OK” Printing Menu Map…
42.XX.YY Printing Registration Page…
47.00.XX Printing stopped
47.01.XX Printing Supplies Status Page…
47.02.XX Printing Usage Page…
47.03.XX Printing…engine test
47.04.XX Processing duplex job Do not grab paper until job completes
47.05.00 Processing job from tray {X}... Do not grab paper until job completes
47.06.XX Processing... copy {X} of {Y}
47.WX.YZ Printer Calibration Failed To continue touch “OK” Processing…
49.XX.YY To continue turn off then on RAM disk device failure
51.00.YY Error RAM disk file operation failed
52.XX.00 Error To continue turn off then on RAM disk file system is full
54.XX.YY Error RAM disk is write protected
55.00.YY DC controller error RAM disk not initialized
55.0X.YY DC controller error Ready
56.00.YY Error Ready {IP Address}
57.00.0Y Error Receiving Upgrade
58.00.0Y Error Remove one print cartridge
59.00.YY error Remove USB accessory
59.A2.0x Error Replace {supply}
60.00.0Y Tray {Y} lifting error Replace supplies
62.00.00 No system To continue turn off then on Resend external accessory firmware
65.X0.A1 Output accessory disconnected Resend Upgrade
66.80.YY Stapler/Stacker failure Restore Factory Settings
69.11.YY Error To continue turn off then on ROM disk device failed
70.00.00 Error ROM disk file operation failed
79.XX.YY Error ROM disk file system is full
80.0X.YY Embedded JetDirect error ROM disk is write protected
81.YY.ZZ EIO-1 Card Failure ROM disk not initialized
82.73.46 OR 82.73.47 Rotating Motor
98.00.01 Corrupt data in firmware volume Size Mis-Match
98.00.02 Corrupt data in solutions volume Size mismatch in Tray {X}
98.00.03 Corrupt data in configuration volume Sleep mode on
98.00.04 Corrupt data in job data volume Staple Cartridge low
99.00.01 Upgrade not performed file is corrupt Staple Cartridge very low
99.00.02 Upgrade not performed timeout during receive Stapler/Stacker staple jam
99.00.03 Upgrade not performed error writing to disk Supplies low
99.00.04 Upgrade not performed timeout during receive SUPPLY MEMORY WARNING
99.00.05 Upgrade not performed timeout during receive The unit has corrupt data
99.00.06 Upgrade not performed error reading upgrade Tray {X} empty: [Type] [Size]
99.00.07 Upgrade not performed error reading upgrade Tray {X} lifting
99.00.08 Upgrade not performed error reading upgrade Tray {X} open
99.00.09 Upgrade canceled by user Tray {X} overfilled
99.00.10 Upgrade canceled by user Type mismatch Tray
99.00.11 Upgrade canceled by user Unsupported drive installed
99.00.12 Upgrade not performed the file is invalid Unsupported supply in use OR Unsupported supply installed To continuetouch “OK”
99.00.13 Upgrade not performed the file is invalid Unsupported tray configuration
99.00.14 Upgrade not performed the file is invalid Unsupported USB accessory detected Remove USB accessory
99.00.2X Upgrade Error
99.09.60 Unsupported disk USB accessory not functional
99.09.61 Unsupported disk USB hubs are not fully supported Some operations may not work properly
99.09.62 Unknown disk USB is write protected To clear press “OK”
99.09.63 Incorrect disk USB needs too much power
99.09.64 Disk malfunction USB needs too much power Remove USB and Then Turn Off then On
99.09.65 Disk data error USB not initialized
99.09.66 No disk installed USB storage accessory removed Clearing any associated data
99.09.67 Disk is not bootable please download firmware USB storage device failure To clear press “OK
99.XX.YY USB storage file operation failed
Accept bad signature USB storage file system is full
Bad optional tray connection Used supply installed To continue touch “OK” OR Used supply in use
Canceling Waiting for tray {X} to lift
Canceling... {jobname} Windows Login Required to Use this Feature
Cartridge Low