HP LaserJet CM4540 Laser Multifunction Printer - Color - Plain Paper Print - Desktop - Printer, Copier, Scanner - 42 ppm Mono/42 ppm Color Print - 600 x 600 dpi Print - 42 cpm Mono/42 cpm Color Copy - Touchscreen - 600 dpi Optical Scan - Automatic Duplex

Error Codes and Support

Error:

{binname} full Remove all paper from bin 99.09.64 Disk malfunction
10.00.70 Printing past very low 99.09.65 Disk data error
10.0X.90 Replace {Supply} 99.09.66 No disk installed
10.0X.Y0 Supply memory error 99.09.67 Disk is not bootable please download firmware
10.XX.69 {Supply} very low To continue touch “OK” 99.09.68 Expecting secondary disk
10.YY.60 {color} cartridge low Accept bad signature?
11.00.YY Internal clock error To continue touch “OK” Authentication required
13.WX.EE Door open jam Authentication required to use this feature
13.WX.FF Jam Bad optional tray connection
13.WX.YZ Fuser Area Jam Calibration reset pending
13.WX.YZ Fuser wrap jam Card slot device failure To clear touch “OK”
13.WX.YZ Jam below control panel Clear jam then touch "OK" Card slot file system is full
13.WX.YZ Jam in left cover Card slot is write protected
13.WX.YZ Jam in lower bin area Card slot not initialized
13.WX.YZ Jam in top cover area Cartridge ship mode
13.WX.YZ Jam in Tray {X} Chosen personality not available To continue touch “OK”
13.WX.YZ Jam in Tray 1 Clear jam then touch "OK" Cleaning disk {X}% complete Do not power off
13.WX.YZ Jam inside lower right door Close front door
13.WX.YZ Jam inside output accessory bridge Close lower right door
13.WX.YZ Jam inside right door Close right door
13.WX.YZ Jams inside lower right door Close top cover
13.WX.YZ Jams inside right door Close upper right door
13.WX.YZ Staple jam inside left cover Code CRC error Send full RFU on {X} port
20.00.00 Insufficient memory: {Device} To continue touch “OK” Color RFU failed Send full RFU on {X} port
21.00.00 Page Too Complex To continue touch “OK” Communication Lost
30.01.06 Scanner Failure Connect output accessory
30.01.08 Scanner Failure Data received To print last page press “OK”
30.01.10 Scanner Failure Digital send communication error
30.01.14 Scanner Failure Document feeder bin full
30.01.15 Scanner Failure Document feeder kit low
30.01.18 Scanner Failure Document feeder kit very low To continue touch “OK”
30.01.19 Scanner Failure Document feeder top cover open
30.01.23 Scanner Failure EIO {X} disk not functional
30.01.36 Scanner Failure EIO device failure
30.01.41 Scanner Failure EIO device failure To clear touch “OK”
30.01.42 Scanner Failure EIO file operation failed
30.01.43 Scanner Failure EIO file system is full
30.01.44 Scanner Failure EIO is write protected
30.01.45 Scanner Failure EIO not initialized
30.01.46 Scanner Failure Expected drive missing
30.01.47 Scanner Failure Fax is disabled – ignoring call
30.01.48 Scanner Failure Finisher low on finishing agent
30.01.49 Scanner Failure Finishing process not functional
30.01.50 Scanner Failure Flatbed cover open
31.01.02 Jam in document feeder Fuser Kit Low
31.01.03 Document feeder pick error Fuser Kit Very Low To continue touch “OK”
40.00.01 USB I/O buffer overflow To continue touch “OK” Gateways failed
40.00.02 Embedded I/O buffer overflow To continue touch “OK” Genuine HP supply installed
40.00.03 EIO {X} buffer overflow To continue touch “OK” HP Secure drive disabled
40.00.04 EIO {X} bad transmission To continue touch “OK” Incompatible {Supply}
40.00.05 Embedded I/O bad transmission To continue touch “OK” Incompatible Supplies
41.02.00 Error To continue touch “OK” Install {color} cartridge
41.03.YZ Unexpected size in tray {X} Install Fuser Unit
41.05.YZ Unexpected type in tray {X} Install Supplies
41.07.YZ Error To continue touch “OK” Install Transfer Unit
42.XX.YY Error Internal disk device failure To clear touch “OK”
44.01.XX Error Internal disk file operation failed
44.03.XX Error Internal disk file system is full
44.34.XX Error Internal disk is write protected
44.92.XX Error Internal disk not found
47.00.XX Error Internal disk not functional
47.01.XX Error Internal disk not initialized
47.02.XX Error Job not stapled due to mixed sizes
47.03.XX Error Load Tray {X}: [Type] [Size]
47.04.XX Error Load Tray {X}: [Type] [Size] To use another tray touch "Options"
47.06.XX Error Load Tray 1 [Type] [Size]
47.WX.YZ Printer Calibration Failed To continue touch “OK” Load Tray 1 [Type] [Size] To continue touch “OK”
49.21.49 The device has a detection problem Load Tray 1 [Type] [Size] To use another tray touch "Options"
49.XX.YY Error To continue turn off then on Manually feed output stack Then touch "OK" to print second side
50.1X.YZ or 50.W2.YZ Fuser Error To continue turn off then on Manually feed: {Type}{Size}
50.3X.YZ Fuser Error To continue turn off then on Manually feed: {Type}{Size} To continue touch “OK”
50.4X.YZ Fuser Error To continue turn off then on Manually feed: {Type}{Size} To use another tray press “OK”
50.7X.YZ Fuser Error To continue turn off then on Moving solenoid and motor To exit press
50.8X.YZ Fuser Error To continue turn off then on Moving solenoid To exit press
50.9X.YZ Fuser Error To continue turn off then on Output Bin Full
50.AX.YZ Fuser Error To continue turn off then on Paperless ModeDescription
50.BX.YZ Fuser Error To continue turn off then on RAM disk not initialized
51.00.YY Error To continue turn off then on Reattach output bin
52.00.00 Error To continue turn off then on Receiving Upgrade
52.20.00 Error To continue turn off then on Remove all print cartridges To exit press
53.10.0X Unsupported DIMM Remove at least one print cartridge To exit press
54.00.03 Error Remove shipping sheet
54.00.06 Error Remove USB accessory
54.00.35 Error Replace DIMM {X} MEM test failure
54.01.05 Error Replace Fuser Kit
54.0X.07 Error Replace staple cartridge
54.0X.0B Error Replace Supplies
54.0X.0C Error Replace Toner Collection Unit
54.0X.0D Error Replace Transfer Kit
54.0X.0E Error Resend external accessory firmware
54.0X.1E Error Resend Upgrade
54.1X.1E Error Restricted from printing in color
54.2X.1E Error RFU Load Error Send full RFU on {X} port
55.00.05 Engine Firmware RFU Error To continue turn off then on ROM disk not initialized
55.00.YY DC Controller Error To continue turn off then on Rotating {color} Motor To exit press
56.00.01 Illegal Input Printer Error To continue turn off then on Rotating Motor To exit press
56.00.YY Error To continue turn off then on Sanitizing disk {X}% complete Do not power off
58.00.04 Error To continue turn off then on Size mismatch in Tray {X}
59.00.00: Paper path malfunction Sleep mode on
59.00.30 Fuser motor (M2) start up error or fuser motor (M2) rotational error Staple Cartridge low
59.00.40 Fuser motor (M2) start up error or fuser motor (M2) rotational error59.00.40: Fuser motor (M2) start up error or fuser motor (M2) rotational error Staple Cartridge very low
59.00.90 ITB motor (M1) start up error or ITB motor (M1) abnormal rotationalerror Staple Cartridge very low To continue touch “OK”
59.00.A0 ITB motor (M1) start up error or ITB motor (M1) abnormal rotationalerror Supplies in wrong position
59.00.B0 Cleaning motor error Replace Toner Collection Unit Supplies low
59.00.C0: Developer alienation motor (M10) error Supplies very low To continue touch “OK”
59.00.F0: T1 alienation mechanism failure The Device Fan Has Failed
59.0X.50 Error To continue turn off then on Toner collection unit almost full
59.0X.60 Error To continue turn off then on Too many jobs in queue
60.00.0Y Tray {Y} lifting error Too many pages in job to staple
62.00.00 No system To continue turn off then on Transfer Kit low
65.80.A1 Output accessory disconnected Transfer Kit very low To continue touch “OK”
66.80.YY {Output device} failure Tray {x} empty
69.11.YY Error To continue touch “OK” Tray {X} empty: [Type] [Size]
70.00.00 Error To continue turn off then on Tray {X} open
79.XX.YY Error To continue turn off then on Tray {X} overfilled Remove excess paper
80.0X.YY Embedded JetDirect Error To continue turn off then on Tray {X} overfilled To use another tray press “OK”
80.YYYY EIO Error To continue turn off then on Troubleshooting To exit press
98.00.01 Type Mismatch Tray
98.00.02 Unable to Install
98.00.03 Unsupported drive installed
98.00.04 Unsupported supply in use
99.00.01 Upgrade not performed file is corrupt Unsupported supply installed
99.00.02 Upgrade not performed timeout during receive Unsupported tray configuration
99.00.03 Upgrade not performed error writing to disk Unsupported USB accessory detected Remove USB accessory
99.00.04 Upgrade not performed timeout during receive Upgrade complete To continue turn off then on
99.00.05 Upgrade not performed timeout during receive Upper bin full
99.00.06 Upgrade not performed error reading upgrade USB accessory needs too much power Remove USB Accessory and Turn Off then On
99.00.07 Upgrade not performed error reading upgrade USB accessory not functional
99.00.08 Upgrade not performed error reading upgrade USB hubs are not fully supported Some operations may not work properly
99.00.09 Upgrade canceled by user USB is write protected To clear touch “OK”
99.00.10 Upgrade canceled by user USB needs too much power
99.00.11 Upgrade canceled by user USB not initialized
99.00.12 Upgrade not performed the file is invalid USB storage accessory removed Clearing any associated data
99.00.13 Upgrade not performed the file is invalid USB storage device failure To clear touch “OK”
99.00.14 Upgrade not performed the file is invalid USB storage file operation failed To clear touch “OK”
99.09.60 Unsupported disk USB storage file system is full
99.09.61 Unsupported disk Used supply in use
99.09.62 Unknown disk Used supply installed
99.09.63 Incorrect disk Windows Login Required to Use this Feature